Carmecha PDF Nics

L292 DATASHEET PDF

L Switch Mode Driver for DC Motors Data Sheet · DRIVERS POUR MOTEUR DC. Legislation and Compliance. RoHS Certificate of Compliance. Statement of. STMicroelectronics L Explore Integrated Circuits (ICs) on Octopart: the fastest source for datasheets, pricing, specs and availability. L Switch-mode Driver For DC Motors. DRIVING CAPABILITY V, 30 KHz 2 LOGIC CHIP ENABLE EXTERNAL LOOP GAIN ADJUSTEMENT SINGLE POWER.

Author: Akinoshicage Samukus
Country: Dominica
Language: English (Spanish)
Genre: Photos
Published (Last): 2 September 2017
Pages: 153
PDF File Size: 18.38 Mb
ePub File Size: 9.57 Mb
ISBN: 674-2-56012-333-2
Downloads: 65020
Price: Free* [*Free Regsitration Required]
Uploader: Volrajas

The “one pulse per rotation” opto encoder output is connected to pin 12 of the L FTF where it is. The oscillator determines the switching frequency of the output stage and should be in the range 1 to The current sense resistors R.

The cutoff frequency is: Input Voltage pin 6.

The schematic diagram used for the Laplace analysis of the system is shown in fig. The error signal obtained by the addition of the input and the current feedback signals pin 7 is used to. Total Drop Out Voltage.

In order to be sure that the current loop is stable the following condition is imposed: This input signals is bidirectional so it must be converted to a positive signal ba. From this basic input, the microprocessor computes datadheet 5-bit control word that sets the system. Inhibit Low Level pin 12, The L internal reference voltage is also derived from V. STMicroelectronics products are not.

L292 Datasheet PDF

The braking is applied progressively until the motor is running at minimum speed. Total Power Dissipation T.

  GROVE RT530E-2 PDF

Motor current is regulated by an internal loop in the L which is performed by the resistors R. This can be foud from: Using the coparators C. Input Voltage pin 6. Download datasheet Kb Share this page.

From this basic input, the microprocessor computes a 5-bit control word that sets the system speed dependent on the distance to travel. It is possible to synchronize datasbeet L ‘s, if desired, using the network shown in fig. Input Offset Voltage pin 6. The device may be used separately – particularly the L motor driver – but since they will usually.

L Datasheet PDF –

This input signals is bidirectional so dayasheet must be converted to a positive signal bacause the L uses a single supply voltage. The system operates in two modes to achieve high speed, high-accurancy positioning. L The system operates in two modes to achieve datasueet speed, high-accurancy positioning. Datasgeet maxi- mum speed is reached, the tachometer chip output backs off the processor signal thus reducing accel- ering torque. The optical encoder also provides an output at one position on the disk datashet is used to set the initial position.

The interval between one side of the bridge switching off and the other switching on, t, is programmed by. Note that in practice R must greater than 5. C17 in conjuction with an internal resistor Rt. When the motor is stopped and the microprocessor orders it to a new positio, the system operates initially in an open-loop configuration as there is no feedback from the tachometer generator.

  LIBRO LA SANTA CRUZ DE CARAVACA TESORO DE ORACIONES PDF

Thus the output stage may be inhibited by taking pin 12 high or by taking pin 13 low.

Datasheet «L292»

The transfer function 3 can be written as follows: The previous linear analysis is correct for this example. Copy your embed code and put on your site: The L, L and L are intended to be used as a 3-chip microprocessor controlled positioning system. This same reference voltage supplies the triangle wave oscillator whose frequency is fixed by the external. Sensing Rsistor Voltage Drop. In order to achieve good stability, the phase margin must be greater than 45?

L STMicroelectronics Switch-mode Driver For Dc Motors ChipFind Datasheet Archive |

The second input to each multipler consists of the sign of l92 first input of the other multiplier before dif. Search field Part name Part description. The “one pulse per rotation” opto encoder output is connected to pin datssheet of the L FTF where it is squared to give the STF logic output for the micro- processor.

Speed commands for the system originate in the microprocessor continuosly updated on the motor position by means of pulses from the L tachometer chip, whitch in tur gets its information from the op- tical encoder.